Total 6 it technician job vacancies in Bayan Lepas

Key Duties and Responsibilities

1. To execute corrective measures with high efficiency whenever there is a breakdown and record down the clear definition of corrective actions in B-core CMMS.
2. To support machine product EWAK changeover or conversion activities to ensure changeover time range fulfill operation target setting.
3. To support module engineer for workstation and equipment setup and troubleshooting
4. To assist maintenance engineer achieve department goals and KPIs.
5. To attend all breakdowns promptly
6. To assist module engineer for fixture/tool modification and replacement.    
7. Support PM task base on real time condition required, planned schedule or manpower availability.
8. Maintain 5S in work area and comply with Bosch health and safety compliance
9. To support on any other section related duties assigned to current team.
10. Comply with safety ground rules and requirement to carry out the maintenance.

1.Role                                                                                                                                                                       1.1 Work with VSO, VSE & Supervisors to maintain, analysis, improve and resolve
production line issues in a responsible manner towards ensure manufacturing meeting Safety, Quality, Cost, and Delivery with guidance from Technician 3.
1.2 Responsible for 1st level failure analysis of reject tools or components from production
line to identify process or supplier related issue for failures which are unable to be solve
by shopfloor leaders.
1.3 Support VSE to perform Machine and Process Capability Study to ensure machines and processes meet the capability requirement during new product introduction and mass production with guidance from Senior Technician.

2.Job Scope
2.1 To perform Process Study on Failure Analysis for existing responsible products on all reject & assist time study, cycle time on the process or ISIR sample build / test in production.
2.2 To assist Manufacturing Changeover activities and perform Evaluation / Rejects activities.
2.3 To assist on technical report Cgk, Cmk, GRR, SPC & etc assigned by Process Engineer/Supervisor.
2.4 To assist Manufacturing Engineering document: Visual aids PQI, work instructions WI, 7S photo, Inspector Work Sequence, Quality Alert & Quality awareness presentation material for briefing purpose.
2.5 To perform daily complaint of raw material to PUQ and assist in scrap preparation if necessary.
2.6 To train and monitor repairers on daily rework activities.
2.7 To support Production in achieving the effectiveness/productivity, output, FOR and quality target.
2.8 To support and involve in BPS activities such as Point CIP projects, LLD, Change Over, TPM or process/product improvement.
2.9 To participate in all scraping audits, coordinate in providing and implementing corrective actions.
2.10 To prepare & submit the scrap form which need submitted daily scrap for management
approval.
2.12 Support VSE/FPV in Machine and Process Capability Studies to ensure new machine and
process meet the capability requirement during new product introduction and mass
production.
2.13 Support VSE/FPV in coordination of PDP project sample build (Pre-Pilot and Pilot run) on
material availability and jig and fixtures readiness.
2.14To assist the Process Engineer / Supervisor in the day-to-day operation.
2.15To support an acting as supervisor if Supervisor & LO no turn up.
2.16To carry out any other duties assigned by immediate superior time to time.

Job Description

1. Job Summary

1.1 Responsible to ensure all equipment used in test center in good working condition.

1.2 Responsible to arrange daily planned job to test worker.

1.3 Responsible to brief test worker on any newly introduced test item or test method.

1.4 Responsible to prepare Test Material, Test Data Recording Sheet for each test.

1.5 Responsible to ensure test material fulfill test plan specification and control the usage.

1.6 Responsible to perform audit at test center and feedback any finding to superior promptly.

1.7 Responsible to perform product function check, internal inspection after test.

1.8 To perform failure analysis.

1.9 To generate and publish test report after completion of the test.

1.10 Specific task assigned by the superior, as and when necessary, to meet target or deadline.

2. Core Competencies

2.1 Able to use basic measuring equipment such as caliper, multimeter & etc.

2.2 Proficiency in spoken and written English and Bahasa Malaysia.

2.3 Basic computer literacy (e.g. Microsoft Excel and Word)

2.4 Good communication skills

3. Work Conditions

3.1 Able to work on shift

3.2 High inter and intra departmental interaction

3.3 Able to work under tight schedule

• Key person to run and support automated EC motor production lines (max. 2 lines) and to solve any ad hoc issues in production (including maintenance and adjustment of machines to achieve defined quality and output).
• The person must be able to run the automated production lines independently, taking up roles similar to combination of operator, POUP, line leader and maintenance technician for manual assembly lines. The goal is to sustain the highly automated EC motor lines with OEE of 85% and above.
• Main tasks include:
• 1.1 Responsible for model changeover including machine setup and parameter changes.
• 1.2 Responsible to perform machine troubleshooting whenever necessary.
• 1.3 Responsible for corrective and preventive maintenance of the lines including spare parts.
• 1.4 Responsible for 1st article confirmation at beginning of the shift and after every changeover.
• 1.5 Responsible for raw material ordering, replenishing of raw material to machines during
• production.
• 1.6 Responsible for 1st level failure analysis of reject parts or components from production line to
• identify process or supplier related issue for failures.
• 1.7 Responsible to confirm non-conformance part and perform inspection and rework activity
• whenever necessary.
• 1.8 Responsible for relevant production KPIs of the line e.g. hourly output, OEE, FOR, quality target,
• 7s etc.
• 1.9 Assist new line setup with machine suppliers, other maintenance technicians, process, and
• equipment engineers.
• 1.10 Support continuous improvement of autonomous and preventive maintenance checklist.
• 1.11 Support training of new EC motor line technicians whenever necessary.
• 1.12 Support samples build in production and pilot run activities for new models.
• 1.13 Participate in daily morning meeting and actively support with line improvement activities.
• 1.14 Other ad hoc tasks as and when required/assigned by superior.
• Remark: Competency must be certified by Electrical Commission (ST) for technicians who are required to exclusively handle electrical installation for the production lines and machines which are operated by an incoming power supply of not more than 415 VAC – single phase/three phase or both.

Job Summary

• Responsible for 1st level failure analysis of reject tools or components from production line to identify process or supplier related issue for failures which are unable to be solve by Failure Analyzer.
• Responsible for monthly FOR (Fall Off Rate) data entry into FOR database for tracking of FOR and Internal Defect Cost (IDC).
• Prepare rework flow for any non-conformities detected at production line for sorting or rework activities.
• Responsible to follow up and track the status of rejected parts complained to supplier via Purchasing Quality engineer (PUQ).
• Responsible to coordinate measurement support activities for verification of part dimension in order to determine root cause of rejection found in the line.
• Update PVS system (Part Verification System) for setting up part number for barcode scanning activities to avoid missing or wrong items been shipped to customer.
• Support VSE in preparing and update In Process Checklist, Production Work Instruction (PWI), Production Quality Indication (PQI) and Quality Alert for daily production usage.
• Assist VSE in preparation of workstations layout, set up workstation and line release documents before Pre-Pilot run, Pilot Run and mass production.
• Support VSE to perform Machine and Process Capability Study to ensure machines and processes meet the capability requirement during new product introduction and mass production.
• Support VSE in coordination of PDP project sample build (Pre-Pilot and Pilot run) on material availability and jig and fixtures readiness.
• Support process improvement project in production through time study - VT improvement, direct productivity improvement, ergonomic, workstation, machine and technology.
• Support production in achieving the effectiveness, output, FOR and quality target through continuous improvement activity.
• Liaise with maintenance personnel for maintenance plan set up and spare parts replacement for existing machine used in production whenever necessary.

Job Scope

• Prepare workstation layout, set up workstation and assist VSE/FPV in preparation of line release documents during pre-pilot run, pilot run and SOP.
• Support VSE/FPV in Machine and Process Capability Studies to ensure new machine and process meet the capability requirement during new product introduction.
• Support VSE in coordination of PDP project sample build (Pre-Pilot and Pilot run) on material availability and jig and fixtures readiness.

 Operation Support

• Responsible for l51 level failure analysis of reject tools or components from production line to identify process or supplier related issue for failures which are unable to be solve by Failure Analyzer.
• Responsible to coordinate measurement support activities for verification of part dimension in order to determine root cause of rejection found in the line.
• Responsible to follow up and track the status of rejected parts complained to supplier via Purchasing Quality engineer (PUQ).
• Responsible for monthly FOR (Fall Off Rate) data entry into FOR database for tracking of FOR and Internal Defect Cost (IDC).
• Support VSE in preparing and update In Process Checklist, Production Work Instruction (PWI), Production Quality Indication (PQI) and Quality Alert for daily production usage.
• Prepare rework flow for any non-conformities detected at production line for sorting or rework activities.
• Update PVS system (Part Verification System) for setting up part number for barcode scanning activities to avoid missing or wrong items been shipped to customer.
• Support production in achieving the effectiveness, output, FOR and quality target through continuous improvement activity.
• Support process improvement project in production through time study - VT improvement, direct productivity improvement, ergonomic, workstation, machine and technology.
• Liaise with maintenance personnel for maintenance plan set up and spare parts replacement for existing machine used in production whenever necessary.
• Coordinate laser marking drawing conversion activity into laser marking machine and ISIR sample submission.

Role:

1.1 Maintenance Technician - To support production on routing shift and performing preventive maintenance, repairs, troubleshooting on equipment & machinery and do method solving & problem on machines at production lines.

Job Scope:

2.1 Conduct basic Repair / troubleshoot machines problem at production line with assist from Technicians 2, 3 or 4.

2.2 Assists in the installation of new equipment and machines.

2.3 To create, execute & update Preventive Maintenance, Autonomous Maintenance for line equipment, machines, and jig/fixtures according to Master Schedule List per Standard defined.

2.4 To liaise with Maintenance Section or Engineer for maintenance plan and spare parts Availability/replacement/controlling.

2.5 Performs routine maintenance tasks, such as cleaning, lubricating, and replacing parts.

2.6 Documents work performed and preventive maintenance records.

2.7 To provide verbal & written communication on equipment downtime, improvement, and document it for future reference.

2.8 To ensure the design and the utilization of the machines & equipment are made according with all the Safety features / regulation.

2.9 To ensure 5s is being carried out at workplace and follow Safety Rules & Regulation during work being carried out.

2.10 To support Ad Hoc tasks assigned by direct superior and other technicians from time to time.